Fully qualified mobile mechanic · Fully insured · Same-day reports 📞 0481 318 451
📞 0481 318 451 Home Standard $250+ Premium $280+ Service Areas About Contact 📞 CALL US TO BOOK
Home / Bayside / Brighton Le Sands

Eastern City District · Brighton Le Sands

From $250 · Standard $250+ recommended

Mobile Pre-Purchase Car Inspection in Brighton Le Sands

Buying a used car in Brighton Le Sands? Our licensed mobile mechanic comes to the seller's address anywhere in Brighton Le Sands and the surrounding Bayside area, checks over 100 points, and gives you a same-day photographed report before you pay a cent.

📞 CALL US TO BOOK 📍 Find your suburb →
✓ Licensed NSW Mechanic
✓ Fully insured
✓ Same-day photographed report
✓ No dealer affiliations

Mobile car inspections in Brighton Le Sands

Brighton Le Sands sits within the Bayside council area along Sydney's southern shoreline, from Botany and Mascot through to Rockdale and Brighton-Le-Sands. Whether you've found a used car on Carsales, Facebook Marketplace, Gumtree or through a local Brighton Le Sands dealer, an independent mechanical inspection is the single most effective way to avoid buying someone else's expensive problem.

We inspect cars at the seller's actual address in Brighton Le Sands — not at a workshop, and not after the engine has already been warmed up. That distinction matters: a cold-start check is one of the most revealing moments of any inspection, showing smoke colour, unusual noises and how quickly oil pressure builds. Sellers who pre-warm a car before a workshop visit remove that evidence entirely, which is exactly why we come to you in Brighton Le Sands instead.

Our Brighton Le Sands inspection typically covers everyday family cars, SUVs, utes and 4WDs, as well as European, prestige, hybrid and electric vehicles. Most bookings in Brighton Le Sands and the wider Bayside are confirmed within a few hours and completed within 24 to 48 hours of your call.

Which package suits a car in Brighton Le Sands?

For most mainstream Japanese, Korean and Australian-market vehicles listed in Brighton Le Sands — think Toyota, Mazda, Hyundai, Kia, Honda and similar — our Standard $250+ inspection covers the full 100+ point mechanical check, OBD-II diagnostic scan, underbody inspection and road test.

If the car you're considering in Brighton Le Sands is a European or prestige brand, a large 4WD, a hybrid or electric vehicle, or is priced above roughly $25,000, we recommend the Premium $280+ package. It adds a 20+ minute mixed-condition road test, digital paint thickness readings on every panel, a module-level scan across engine, ABS, SRS and body control units, and a brake fluid moisture test.

Based on where Brighton Le Sands sits within the Eastern City District, most inspections in this area are priced at $250+ to reflect local travel time — we'll confirm your exact quote when you call to book, based on the make, model and condition of the specific car.

What our mechanic checks on site in Brighton Le Sands

Every Brighton Le Sands inspection includes a cold engine start, full underbody inspection with a torch for rust, oil and fluid leaks, brake and suspension assessment, a real-world road test covering local streets, and a complete interior and electrical function check — every window, lock, seatbelt and dashboard warning light.

We also run a computer diagnostic scan to pull any stored or pending fault codes, check the VIN and compliance plates for consistency against the paperwork, and photograph every fault we find so you have clear, shareable evidence — not just our word for it.

Before we leave the seller's address in Brighton Le Sands, we call you directly with a frank, plain-English summary: buy with confidence, negotiate the price down by a specific amount, or walk away. You'll also receive the full photographed report the same day.

  • Cold engine start and exhaust smoke check
  • Full underbody and rust inspection
  • Brakes, suspension and steering assessment
  • OBD-II and module-level diagnostic scan
  • Real-world road test on local roads
  • Complete interior and electrical function test

Booking an inspection near Brighton Le Sands

To book, call us with the seller's address in Brighton Le Sands, the make, model, year and a link to the listing if you have one. We'll confirm a time — often the same day or next day — and handle the rest directly with the seller, so you don't need to be present or even live locally.

We also regularly inspect cars in the suburbs surrounding Brighton Le Sands, so if the seller is a short drive away in a neighbouring area, that's not a problem.

BotanyWolli CreekRockdaleSans SouciSydenhamBexleyBanksiaRamsgate

Buyer's Guide

Used car buyer's guide — 50 essential questions answered

Everything a Sydney buyer needs to know before handing over a deposit. Our mechanics answer the most important pre-purchase inspection questions in plain English.

Park on level ground with the engine off and cool (or 5–10 minutes after running). Pull the dipstick, wipe clean, reinsert fully, then pull again. Oil should sit between the min and max marks. Fresh oil is amber to light brown and clear. Dark brown but still clear is okay. Black, thick, gritty or milky oil (coolant contamination — a head gasket warning) means trouble. Metal particles or a strong burnt smell are red flags. Low or very dirty oil suggests poor maintenance and should be factored heavily into any buying decision.
Look for coloured puddles (green, red or orange) under the car — especially near the radiator, hoses and water pump. Check the coolant overflow reservoir — if it's low, that's a warning. White smoke from the exhaust on a warm engine means coolant is burning. A sweet smell in the engine bay or exhaust is a coolant indicator. Milky oil on the dipstick or oil cap means coolant has mixed with oil — a serious head gasket fault. Rust or scale in the radiator overflow tank also signals neglected cooling system maintenance.
A brief valve tick on cold start is normal — a persistent deep knock is not. Deep knocking points to rod or bearing wear. Loud ticking from the top of the engine suggests lifters, injectors or an exhaust leak. Under acceleration, knocking or pinging means detonation, poor fuel or timing issues. A rough idle with misfire sounds points to coils, plugs, injectors or a vacuum leak. Rattling from the timing cover area — especially on cold start — often means a worn timing chain or tensioner, which is expensive to repair.
Blue smoke means the engine is burning oil — worn piston rings, valve seals or turbo seals. It is most visible on deceleration or after the car has been idling. White smoke (thick, sweet-smelling, slow to clear) means coolant is burning — head gasket, cracked head or cracked block. Black smoke means a rich fuel mixture — clogged air filter, bad injectors, faulty MAF sensor or turbo boost issues. Diesels can produce some black smoke under heavy load, but it should not be excessive or constant.
On a manual: the clutch should engage smoothly mid-pedal with no slipping (where the revs rise but the car doesn't accelerate), no grinding on shifts, no jumping out of gear and no judder on take-off. On an automatic: look for delayed engagement from Park or Neutral into Drive or Reverse, harsh shifts or clunks, RPM flaring between gears, or slipping under acceleration. Test the manual shift mode if fitted. A transmission repair or replacement is one of the most expensive jobs on any car — thorough testing here is essential.
Look for oily residue at the power steering pump, rack and hoses. Check the fluid reservoir level — low fluid is a warning. When turning the wheel at low speed (especially on a cold engine), listen for whining or groaning — that is either a pump under pressure or air in the system from a slow leak. Steering that feels heavy, inconsistent or pulls to one side despite a straight road also warrants investigation. Electric power steering (no fluid) can still have faults — feel for inconsistent weight across the steering range during the test drive.
Listen for loud rumbling, hissing or a tinny rattle on cold start — exhaust leaks are loudest before the metal expands with heat. Check for soot marks at manifold joints, flexi-pipe connections and welds. A smell of exhaust inside the cabin is a carbon monoxide risk and a serious safety concern. Rattling heat shields are minor but annoying. A cracked exhaust manifold or split downpipe is a real repair cost — budget $500–$1,500 depending on the vehicle.
The best method is to park the car overnight on clean concrete and check for drips in the morning. During inspection, look under the engine, transmission, diff and rear axle for oily residue. Common leak points include the valve cover gasket (top of engine), oil pan gasket (underneath), front and rear main seals, and the turbo oil feed and return lines on turbocharged engines. Wet, dusty oily residue is a slow leak — fresh drips are an active leak. Either needs to be factored into the price.
The clutch pedal should engage mid-travel — not at the very top or the very bottom of pedal travel. A clutch that grabs high up (near the top of the pedal stroke) is worn and close to needing replacement. Slipping means the revs rise under acceleration but the car doesn't respond — the clutch disc is glazed or worn out. Judder on take-off in first gear is a warped or contaminated clutch disc. A new clutch on a typical Sydney car costs $800–$1,800 including labour — factor that into any negotiation if the clutch shows wear.
Automatic transmission fluid (ATF) should be bright red or pinkish-red when new and may darken to a deeper red or light brown with use — still clear, still acceptable. Dark brown or black ATF with a burnt smell is overdue and indicates potential damage. Cloudy, gritty or milky ATF is a serious warning of water contamination or internal wear. For manual gearboxes, the oil is usually amber to brown and thick with a strong gear-oil smell — milky means water contamination. To check ATF: with the engine warm and idling, pull the dipstick (if fitted), wipe on a white tissue and check the colour.
Flood-damaged cars are a real risk in NSW and Queensland. Key signs: mud or silt in wheel arches, under trays and in the boot spare wheel well; water lines or staining on door sills and lower panels; musty or mouldy smell especially under carpets; silt or grit in the cabin air filter, footwells or under seats; fogging or water marks inside the instrument cluster, headlights or tail lights; corrosion on fuse boxes, wiring connectors and under-dash wiring; and multiple simultaneous electrical faults — windows, locks, ABS, airbags. Always run a PPSR check at psr.gov.au. If you suspect flood damage, walk away.
Listen for: engine knocking or tapping under load; transmission clunks or harsh shifts; suspension clunks and squeaks over bumps; brake squeal or grinding; power steering whine; exhaust rattles; wind or tyre noise suggesting seal or alignment issues. Feel for: pulling left or right under braking or on a straight road; vibration in the steering wheel at speed; vibration through the seat or floor; a soft or spongy brake pedal; clutch judder or slipping; harsh or delayed gear changes. Try city streets, a hill and highway speed if possible.
Not necessarily. A well-documented independent service history by a reputable local mechanic is often better than spotty or incomplete dealer history. What matters most is consistency, correct fluids and parts, correct intervals, and clear records for major items like timing belts, clutches and transmission services. A car serviced at the same trustworthy workshop every year is a better buy than one with patchy dealer history where major intervals have been skipped. Always check that the service dates, odometer readings and job records make sense — gaps, backwards odometer readings or missing major services are serious red flags.
High-km cars (over 120,000 km) with no service history at all are high risk and usually best avoided for a daily driver. Without proof of timing belt, clutch, transmission service and oil changes, you are inheriting unknown risk. That said, if the price is significantly below market, you have had a thorough independent inspection (including compression and leak-down testing), and you are prepared to immediately do all major services, it can work — but only with expert help. If the seller is vague, defensive or dismissive about history, that is a strong signal to walk away regardless of the price.
Red flags for forged logbooks: stamps or logos look blurry, pixelated or inconsistent with the dealer's or mechanic's known branding; handwriting or fonts are inconsistent across pages; dates or odometer readings don't follow a logical progression; no mechanic details — business name, ABN, address, phone; or services recorded at impossible intervals. To verify: call the mechanic or dealer listed and confirm the service. Cross-check odometer readings against registration certificates or PPSR history. If you have any doubt, treat the logbook as missing entirely.
The most common scams: deposit scams where the seller asks for a bank transfer or PayID to 'hold' the car before any inspection; fake photos using stolen images from other listings; too-good-to-be-true pricing well below market value; overseas seller scams ('I'm overseas, we'll ship it via eBay'); and curbstoners — unlicensed dealers posing as private sellers flipping written-off or flood-damaged cars. The rule is simple: never pay anything before inspecting the car in person, verifying the VIN, and running a PPSR check. No exceptions.
Never. This is a classic scam pattern. Once you pay a deposit, the seller may ghost you, claim it went to another buyer, or the car turns out to be completely different from the listing. You have almost no legal recourse in a private sale transfer. The correct order is: inspect first, negotiate second, pay only when you are ready to sign a proper sale contract and take possession. Any seller who pressures you to pay a deposit before you have seen the car in person is either running a scam or hiding something about the car.
A curbstoner is an unlicensed dealer posing as a private seller to avoid consumer law obligations. Signs include: multiple cars listed at the same time or repeatedly over time with similar descriptions; unwillingness to provide a home address — only neutral carpark meets; cars that were recently registered or have only been owned for a few weeks; vague service history or ownership stories; pressure for quick sale, cash only or deposit before inspection; and vehicles that later turn out to have written-off, flood or odometer histories. Search the seller's phone number across Marketplace and Gumtree. Check how long they have owned the car via Service NSW registration history.
These phrases are sometimes genuine — an executor liquidating an estate, a family needing a quick sale — but they are also extremely common pressure tactics used by scammers and curbstoners. Be cautious if the seller discourages a pre-purchase inspection, asks for a deposit before you have seen the car, cannot provide clear ownership documents, or is vague about why they are selling. A legitimate urgent sale can happen, but the urgency of the seller is never a reason to skip the inspection, skip the PPSR check, or hand over money before you have full confidence in what you are buying.
The classic bounce test: push down firmly on each corner of the car, then release. The car should settle in one or two bounces. If it bounces more than that, the shocks are worn. Also look for oil leaks down the shock absorber body — a wet or oily shock is already past its useful life. On the test drive, worn shocks feel floaty at speed, cause excessive nose-dive under braking, and allow the rear to squat heavily under acceleration. Suspension that bounces excessively over speed humps is a clear sign. Each shock absorber costs $150–$400 to supply and fit, depending on the car.
Even wear across the full tread width is what you want — it means the alignment, inflation and suspension are all correct. Inner or outer edge wear means the alignment or camber is out. Wear only in the centre means the tyres have been consistently over-inflated. Wear on both shoulders means consistent under-inflation. Cupped or scalloped wear (high and low spots around the tyre) means the shock absorbers or suspension bushings are worn. Also check the tyre age code: the last four digits stamped on the sidewall (week and year of manufacture). Tyres over 6–7 years old should be replaced regardless of tread depth.
A clicking noise when turning sharply — especially in a tight circle — is the classic sign of a worn outer CV joint. The noise tends to get louder as the joint wears. A clunking noise under acceleration (especially from a standstill) points to worn inner CV joints or a driveshaft. Inspect the CV boots: torn or cracked rubber boots allow grease to escape and dirt to enter — once a boot is torn, the joint is on borrowed time. If you see grease splattered around the inner wheel arch or driveshaft area, the boot has been split for some time. A CV joint replacement costs $200–$500 per side depending on make and model.
Crouch down and look inside each wheel arch — especially the rear ones, which trap water and mud. Surface rust on bolts and minor surface scale is normal on older cars, but flaking, pitting or bubbling metal is structural rust that needs attention. On the underbody, check the chassis rails, floor pans, sill seams and spare wheel well (remove the boot carpet). Rust that has eaten through the metal in structural areas is a serious safety issue. Patch-repaired rust that has been painted over feels soft when pressed — or sounds dull rather than solid when tapped. Our Premium 280+ inspection includes a torch-lit underbody rust check.
Colour differences between panels (especially visible in natural light or from an angle) suggest the car has had panel work done after a crash or significant damage. Look for: overspray on rubber window seals, trim pieces or plastic brackets; texture differences (orange peel) between panels that don't match factory finish; tape or masking lines around panel edges; and fresh paint smell in a supposedly older car. A car that has been repainted after a crash raises questions about what structural work was done underneath. The paint thickness gauge in our Premium 280+ inspection is the most reliable way to detect this.
Smell the car first — a musty or mildew smell, especially when the air conditioning is on, is a strong indicator of water ingress. Pull back the carpet in the front footwells and boot: wet or damp carpet, water staining or rust under the carpet all indicate a leak. Check the headlining for water marks or sag. On sunroof-equipped cars, check that the drain channels are clear — blocked sunroof drains are the most common cause of interior water ingress. Look for fogging or condensation inside the headlight and tail light clusters — that also indicates moisture in sealed areas.
Operate every window up and down — both from the driver's master switch and from each individual door switch. Slow or jerky window movement points to motor or regulator wear. Test central locking from the driver's button, the key fob, and the passenger door. Try child safety locks on rear doors. Test the infotainment: radio, Bluetooth pairing, USB, navigation screen touch response. Check every wiper speed and both front and rear washer jets. Press every button on the dashboard and steering wheel. Start the car and watch the dashboard warning lights — they should all come on briefly and then go off. Any persistent warning light needs to be explained before you buy.
All warning lights should illuminate briefly on start-up (self-test) and then turn off. A persistent engine warning (check engine) light means a stored fault code — could be minor (sensor) or major (engine or emissions fault). ABS light: the anti-lock braking system is not working — a safety issue. Airbag / SRS light: the airbag system has a fault — the bags may not deploy in a crash. Transmission warning: gearbox fault — potentially expensive. 4WD warning: transfer case or diff fault. Any light that stays on or comes on during the test drive needs to be scanned with a diagnostic tool before purchase.
The first 30 seconds of a cold engine startup is the single most diagnostic moment of any pre-purchase inspection. On a cold start you can see: smoke colour (blue, white or black); hear unusual noises that disappear once the engine warms (timing chain rattle, rod knock, valve tick); observe how quickly oil pressure builds; and watch for rough idle, misfires or hesitation that clear once the engine warms. A seller who warms the car up before you arrive has effectively destroyed this data. Our mechanics always insist the car is cold — not started that morning — before we begin any inspection.
Many modern engines are interference engines — if the timing belt snaps, the pistons collide with the open valves, causing catastrophic and usually uneconomical engine damage. Timing belts typically need replacing every 80,000–120,000 km or 5–8 years, depending on the make and model. Always check the service history for documented timing belt replacement with date and odometer. If there is no record and the car is near or over the interval, budget $600–$1,500 for belt, water pump and labour at a reputable Sydney workshop — or negotiate that amount off the price. On an interference engine with no timing belt proof and high kilometres, walking away is often the right call.
When you start the car, the ABS and traction control warning lights should come on briefly (self-test) and then go off. A light that stays on means there is a fault in the system — the ABS or traction control is not functioning, which is both a safety issue and a negotiating point. During the test drive on a safe surface, a gentle firm brake at low speed should produce a slight pulsation through the pedal — that confirms the ABS is engaging. Any car with persistent ABS, stability control or traction warning lights needs a diagnostic scan before purchase.
Check the battery date code — usually a sticker or embossed code showing the week and year of manufacture. A battery over four to five years old is at high risk of failure in Sydney's climate. Look for corrosion (white or green powder) on the terminals, a cracked case, or loose terminal clamps. Measure the voltage: a healthy battery should read around 12.6V with the engine off and 13.8–14.4V with the engine running (showing the alternator is charging). Our Premium 280+ inspection includes a battery cranking-amp test and state-of-health log — the most accurate way to assess remaining battery life.
Through most alloy wheels you can see the brake caliper and the disc rotor. Look at the inner pad — if the pad material looks very thin (under 3 mm), replacement is due soon. The disc should look relatively smooth — deep grooves, heavy rust on the face, or cracks are all concerns. Uneven wear between left and right suggests a sticking caliper. Listen during the test drive: squealing on light braking is worn indicator tabs; grinding means the pad is completely gone. Brake pad and disc replacement costs $300–$600 per axle at most Sydney workshops.
No — this is one of the most well-known car scams operating in Australia right now. The seller claims to be overseas, wants to arrange shipping via eBay Motors or a courier, and asks for payment via wire transfer, Western Union, crypto or PayPal Friends and Family. The car either does not exist or is not what was advertised. For all Australian used car purchases: buy locally, inspect the car in person, verify the VIN, run the PPSR check (psr.gov.au), and transfer money only at or after the time of physical handover. There is no legitimate reason for an Australian-registered private car to be sold by an overseas seller.
PPSR stands for Personal Property Securities Register — it is the Australian government database that shows whether a car has any money owing (finance encumbrances), has been reported written-off, has a stolen flag, or has an odometer discrepancy recorded. A PPSR check costs $2 and takes two minutes at psr.gov.au. It is the single cheapest and most important check a buyer can do before committing to a purchase. Always run the PPSR before handing over any money. We walk every client through interpreting the results as part of our inspection service — a clean PPSR is important but not the whole picture.
Yes — and most buyers do. Our reports are written to be shown directly to the seller. They are itemised, photographed and clearly rated as pass, advisory or fail, with repair cost estimates for every fault found. Most Sydney sellers accept a price reduction supported by an independent inspection report without argument — because the alternative is to fix the issues themselves and re-list the car. The most common outcome is a price reduction equal to or greater than the estimated repair costs. Many buyers tell us they saved more than the inspection fee in the first five minutes of showing the report to the seller.
We inspect all petrol and diesel cars, SUVs, utes, vans and light trucks — including Toyota, Mazda, Hyundai, Kia, Honda, Subaru, Nissan, Ford, Holden, Mitsubishi, BMW, Mercedes-Benz, Audi, Volkswagen, Volvo, Lexus, Land Rover, Porsche, BYD, MG and most other brands sold in Australia. We also inspect EVs and hybrids including Tesla Model 3 and Model Y, BYD Atto 3, Hyundai Ioniq 5 and 6, Kia EV6, Toyota RAV4 Hybrid, Camry Hybrid and most others. We do not inspect motorbikes, heavy trucks or caravans.
Our Standard 250+ inspection starts from $250. This covers most everyday Japanese, Korean and mainstream Australian-market vehicles. Our Premium 280+ inspection starts from $280 and is recommended for European brands, prestige vehicles, performance cars, large 4WDs, modified vehicles and anything priced above $25,000. Pricing depends on location — Eastern City suburbs are mostly at the $250 rate; North, Central and South West districts are mostly at the $280 rate to reflect travel and the local vehicle mix. There are no hidden fees, no travel surcharges and no payment until after the inspection is complete.
Yes. We test every 4WD system we encounter — including part-time 4WD (4H/4L), full-time AWD, and electronic on-demand systems. We engage and disengage the system, listen for binding, clunks or grinding, check the transfer case and front differential for leaks and noise, verify that 4WD warning lights behave correctly, and confirm proper engagement on a low-traction surface where safe and available. 4WD system faults are common and expensive — a transfer case rebuild can cost $3,000–$8,000. We check it every time.
Private car sales in NSW are sold 'as is' — once money changes hands, the buyer has very limited legal recourse for undisclosed mechanical faults. If you buy a car without an independent inspection and it has a failed head gasket, worn transmission, undisclosed crash damage or a stretched timing chain, you own the repair bill. The average unexpected major repair cost on a used car in Sydney is between $2,000 and $8,000. Against that risk, a $250–$280 inspection is the cheapest insurance a buyer can have — and it either saves you money by finding faults, or gives you confidence by confirming the car is exactly what it appears to be.
A workshop inspection has one critical flaw: the seller has to drive the car there. By the time it arrives, the engine is warm and the cold-start data — the most important diagnostic moment of any inspection — is gone. Cooling system faults, oil pressure irregularities, starter motor weakness and morning smoke that clear up after warm-up are all invisible. Our mobile inspection solves this by coming to the seller's address while the car is cold. We also get to see the car in its actual environment — oil stains under where it parks, the state of the garage, the other vehicles on the property — all of which add to the overall picture.
Only if the price reflects the full cost of doing the service immediately — and only if you understand the risk. If the car is near or over its timing belt interval (typically 80,000–120,000 km or 5–8 years depending on the make) and there is no documented replacement on record, you need to treat it as an immediate repair job. Budget $600–$1,500 for timing belt, water pump and labour at a Sydney workshop. On interference engines, driving on an unknown-age timing belt is a gamble that can end in catastrophic engine failure and a repair bill that exceeds the car's value. Our inspection always checks for timing belt records and flags this clearly.
We typically confirm inspections within a few hours of your call and inspect within 24 to 48 hours in most Sydney suburbs. If a deal is moving fast and you need a same-day inspection, call us directly — we will do our best to accommodate. We cover the Sydney metro every day of the week and our schedule is managed to handle urgent bookings when they come in.
No. The majority of our Sydney inspections are booked by buyers who are interstate, working or simply too busy to attend. We deal with the seller directly, photograph every issue and call you with a frank verbal walkthrough before we leave the property. You get the full picture without ever having to be in the same suburb as the car.
Walk away. A genuine private seller has nothing to hide and is usually relieved to have a professional third party confirm the car is what they claim. Sellers who refuse a pre-purchase inspection — or who want to limit access to certain areas of the car — almost always have a reason. In our experience, that reason costs the buyer money.
We do not pull the PPSR report ourselves — it is a $2 government check you are better off running under your own name at psr.gov.au. What we do is walk you through exactly how to run it, what each result means, and how to interpret any encumbrance, written-off, stolen or odometer-discrepancy flags. We also check the VIN plate, compliance plate and service history for internal consistency — discrepancies between the paperwork and the physical car are a major red flag we take seriously.
Bank transfer, Apple Pay, Google Pay, Visa, Mastercard and direct EFTPOS on site. We send a tax invoice immediately. You can also pay by card over the phone before we arrive if you prefer — some buyers find that simpler when they are booking from interstate.
We tell you exactly what we found, what it is likely to cost to fix at a reputable Sydney workshop, and whether the asking price is still sensible given the faults. We are not here to kill every deal — if the car is fairly priced for its condition we say so. But if it is overpriced for what it is, or if there is a hidden fault that would be a nasty surprise after purchase, we will tell you clearly and let you decide what to do with that information.
Yes. We inspect Tesla Model 3 and Model Y, BYD Atto 3, Seal and Dolphin, Hyundai Ioniq 5 and 6, Kia EV6, MG ZS EV, Polestar 2, Toyota RAV4 Hybrid and Camry Hybrid, and most other EVs and hybrids. For EVs we log battery state-of-health where the diagnostic protocol allows, check the 12V auxiliary battery (the most common and most overlooked EV failure point), inspect tyres, brakes and suspension, and review the charge history and energy-use data where accessible.

Ready to book a Sydney inspection?

Send us the listing and the seller's address — we usually inspect within 24 to 48 hours.

📞 CALL US TO BOOK 📍 Find your suburb